Midea aircon error code

There are a number of air conditioning brands out there but MIDEA is one of the most prominent. Here, we are going to look at how to find the right Midea Air Conditioning Error Codes for your device.

Midea aircon error codes

1. E0 – error code will be displayed when the EEPROM data in the indoor unit is abnormal.
2. E1 – error code will be displayed when the communication between indoor and outdoor units is abnormal.
3. E3 – error code will be displayed when there is an abnormal fan speed in the indoor unit.
4. E4 – error code will be displayed when the indoor room temperature sensor has open circuit or short circuit.
5. E5 – error code will be displayed when the evaporator coil temperature sensor has open circuit or short circuit.
6. EC – error code will be displayed when there’s a malfunction of refrigerant leakage detection.
7. EE – error code will be displayed when there’s a malfunction of the water-level alarm.
8. E8 – error code will be displayed when there’s a communication malfunction between two indoor units (for the twins model).
9. E9 – error code will be displayed for other malfunctions of the twins model
10. F0 – Current overload protection Check compressor winding, disconnection, or poor contact of connectors.
11. F1 – Outdoor room temperature sensor open circuit or short circuit Check the connection, if normal check the sensor resistance value, which should be between 15 and 25KΩ/25℃.
12. F2 – Outdoor condenser pipe temperature sensor error Check the connection, if normal check the sensor resistance value, which should be between 15 and 25KΩ/25℃.
13. F3 – Discharging air temperature sensor error.
14. F4 – Outdoor EEPROM error
15. F5 – Outdoor fan speed malfunction (Only for DC fan motor).
16. F6 – T2b sensor error Replace T2b sensor.
17. F7 – The lifting panel communication checking channel is abnormal Replace the mainboard inside the lifting panel.
18. F8 – Lifting panel malfunction Replace the mainboard inside the lifting panel.
19. F9 – Lifting panel is not closed. Replace the mainboard inside the lifting panel.
20. P0 –Inverter module IPM protection Inverter module protection, such as inverter module overcurrent protection, inverter module drive under voltage protection and so on.
21. P1 – High/Low voltage protection. Refrigerant overcharge or undercharge, system circuit failure causes high pressure or low pressure.
22. P2 – High-temperature protection of compressor top. The temperature detected by the thermistor on the compressor top is too high.

    Compressor internal fault or refrigerant leakage causes compressor to overheat. Compressor top overheating due to poor heat dissipation (ambient temperature above 30℃) may also cause the compressor to overheat. 

23. P3 – Outdoor low temp. Protection

    When the outdoor ambient temperature drops below 4℃, the unit may stop for a certain time for compressor frosting protection. When the ambient temperature rises above 4℃, the unit will resume operation automatically. 

24. P4 – Compressor drive error (IPM) The signal feedback from the motor is abnormal during rotation.
25. P5 – Mode conflict.
26. P6 – Inverter inverter module overheat protection.
27. P7 – Overcurrent or short circuit protection
28. P8 – Outdoor EEPROM parameter error
29. P9 – Outdoor unit / indoor unit transmission error.
30. PA – Communication error between outdoor units in parallel operation or cascade connection.
31. PB – Indoor / outdoor unit transmission error (Emergency operation). 
32. PC – Indoor unit EEPROM parameter error.
33. PD – Inverter compressor rotation speed detection circuit abnormal signal input.
34. PE – Input parameter error during full heat pump mode operation. 
    

I hope you found the information I have shared useful and helpful. I will update the aircon error codes if there are new ones. Before you operate the aircon again, turn it off. Wait for 15 minutes or more before operating the a/c again. If there is an error code displayed after the power was turned on, try to see what happened before you turn it on again.